• Address: No.416 Jianye Road South Jinqiao Area Shanghai, China
  • Call Anytime: Tel: +86-21-58386256 +86-21-58386258
  • Conveyor Safety and Preventive Maintenance

    Cam Roller Lubrication and Adjustment - Inspect and adjust cam rollers Both front and rear cam support blocks have provisions for lubrication Front blocks can be lubricated without guard removal To lubricate rear cams, the rear guard must be removed All cam rollers should be checked for proper adjustment (see boom alignment instructions).

    live chat
  • Equipment Guarding By MSHA

    Jul 01, &#; The belt conveyor return roller shown in this photo is compliant It is located 8 inches from the edge of the travelway and about 1 foot above the walkway’s surface Contact would not be inadvertent Return rollers must be guarded when persons work or travel beneath the belt conveyor This photo shows a conveyor located between two travelways.

    live chat
  • Guarding of Belt Conveyors

    GUARDING OF BELT CONVEYORS , 17 Idler rollers 18 Belt and pulley nip guards 20 Other pulleys 21 Projecting shafting , Return idler: Idler roller which supports the empty side of the belt Bend pulley: A pulley used to change the direction of the belt in a vertical plane.

    live chat
  • K-Protector Return Idler Guard: Conveyor Safety

    As well as protecting the workers from pinch point injuries, the site wanted a guard with a fully compliant design that would reduce cleaning downtime, and therefore create opportunities for more proactive maintenance tasks Resolution The site has now installed the K-Protector Return Idler Guard at all of its hazardous and critical nip points.

    live chat
  • Joy Idlers and Return Rolls

    For decades, Joy conveyor idlers have been utilized in some of the most productive material handling applications Joy idlers and return rolls are available for CEMA C, D, E, and F applications CEMA C (ball bearing) Our CEMA C ball bearing roll design features: 20 mm solid shaft; 20 mm ball bearing; Grease-filled, multi-path labyrinth.

    live chat
  • Conveyors and Conveyor Systems

    Easily expandable and portable, these conveyors can be shaped and installed anywhere During the assembly line, a ball transfer table allows workers to easily rotate heavy products and gain access to all sides with minimal effort Improve your workplace's efficiency with the proper conveyors.

    live chat
  • Belt Conveyor Fatal Nip Hazards

    The use of nip point guards in the industry over many years has shown that to fit them is a reasonably practicable measure, which can be easily achieved and at little cost compared to the overall cost of the belt conveyor Nip guards, are essential safety devices and they need to.

    live chat
  • Joy Idlers and Return Rolls

    For decades, Joy conveyor idlers have been utilized in some of the most productive material handling applications Joy idlers and return rolls are available for CEMA C, D, E, and F applications CEMA C (ball bearing) Our CEMA C ball bearing roll design features: 20 mm solid shaft; 20 mm ball bearing; Grease-filled, multi-path labyrinth.

    live chat
  • Guarding Equipment (Canadian) [Read-Only]

    Return Rollers

    GUARDING OF BELT CONVEYORS , 17 Idler rollers 18 Belt and pulley nip guards 20 Other pulleys 21 Projecting shafting , Return idler: Idler roller which supports the empty side of the belt Bend pulley: A pulley used to change the direction of the belt in a vertical plane.

    live chat
  • CONVEYOR SAFETY AND GUARDING

    Nov 02, &#; A good case in point is the request to provide guarding full-length along belt conveyor carrying and return idlers WSBC Part 12 doesn’t have much to say on belt conveyors Section states “A belt conveyor must have accessible nip points of spools and pulleys guarded to prevent contact by a worker.

    live chat
  • Series Belt Conveyors Parts, Assembly & Maintenance

    mounting brackets with return rollers (I) in proper locations 2 Place the section (J), with the drive unit (F) attached, into position on the stands The conveyor belt should be over the top of the return rollers 3 If the bottom wiper/guard was installed on the second section (D).

    live chat
  • Conveyor Pulley, Drive Pulley, Snub Pulley, Take-Up(Tail

    Services : In addition to the supply of our products we provide services like Belts installation joining & maintenance, Rubber lining, Pulley Lagging at your site We also take annual service contract Jagruti rubber offer a 24 hour, 7 days a week, 365 days a year emergency on site break down service.

    live chat
  • Rex Conveyor Idlers

    a unique rounded roll end This EASY Roll protects the belt for longer life The EASY Roll design also keeps the roll shell and end disc junction completely away from the wear area for more idler life Meets or exceeds CEMA load-rating requirements 4" and 5" Diameter Roll Thickness 9 gauge (") increased roll life , B+ Seri.

    live chat
  • Rex Conveyor Idlers

    a unique rounded roll end This EASY Roll protects the belt for longer life The EASY Roll design also keeps the roll shell and end disc junction completely away from the wear area for more idler life Meets or exceeds CEMA load-rating requirements 4" and 5" Diameter Roll Thickness 9 gauge (") increased roll life , B+ Seri.

    live chat
  • Belt Conveyors & Power Belt Systems

    Easier on fragile loads: drives the belt, while roller conveyors drive the load; , Integrated guard rails help contain the load, and is ideal for overhead conveying applications , A wide belt conveyor fitted with fixed belt plows for the purpose of merging cartons from multiple parallel lin Unique belt type for tracking on a low length.

    live chat
  • Return Roller Guard

    INSTALLATION INSTRUCTIONS FOR FLEXI GUARD RETURN ROLLER GUARD The function of the Flexi Guard Return Roller Guard is to provide pinch point protection on conveyor return rollers If the unit is installed correctly the guard meets the Australian Standard AS Modifying the unit in any way may render the unit unsafe and not fit for service.

    live chat
  • return-roll-guard

    We're not around right now But you can send us an email and we'll get back to you, asap.

    live chat
  • belt conveyor return roll guard

    belt conveyor return roll guard; Guarding of Belt Conveyors - gvsafety 17 Idler rollers 18 Belt and pulley nip guards 20 Other pulleys 21 Projecting shafting 21 Belt fasteners and cleats , Return idler: Idler roller which supports the empty side of the belt , Guarding of Belt Conveyors.

    live chat
  • Conveyor Components « CCComponents

    To compliment our extensive range of Conveyor Belt, Conveyor Systems and Industrial Rubber Products, CCComponents Pty Ltd has developed an impressive range of Conveyor Components Our Conveyor Components range is constantly being expanded to meet increased demand from our customers and to reflect new market trends.

    live chat
  • Conveyor components

    Conveyor components Millions of belt conveyor components from have been used to move billions of tons of bulk material since No matter the requirement, we have the conveyor rollers to meet your needs.

    live chat
  • MSHA's Guide to Equipment Guarding

    MSHA’s Guide to Equipment Guarding US Department of Labor Mine Safety and Health Administration , The reason for guarding return idlers is shown in Figure 4 , the pinch points and moving machine parts of both belt conveyors Before removing this guard, both belts would need to.

    live chat